• メインコンテンツにスキップ
  • 二次メニューにスキップ
  • プライマリサイドバーにスキップ
バスルーム-キッチン-蛇口.com

バスルーム-キッチン-蛇口.com

モダンなキッチン蛇口とバスルームのハードウェアデザイン

  • ホーム
  • 製品カタログ
  • 約
  • 連絡先
  • 浴室
    • 浴室の蛇口
      • 洗面器の混合栓
      • クロームトイレ栓
      • ビデミキサー蛇口
      • シャワー水栓
      • 浴槽のシャワーのコック
    • ハンドビデスプレー
    • 浴室の虚栄心のキャビネット
    • 浴室付属品
  • キッチン
    • 引き出し式キッチン蛇口
    • キッチン設備
    • 食器棚の照明
    • ステンレス鋼の台所の流し
  • 蛇口
    • 自動センサー蛇口
    • プラスチック蛇口タップ
    • シングルタップ蛇口
    • 蛇口のメンテナンス
    • 節水蛇口エアレーター
    • 蛇口の取り付けと修理
  • にわか雨
    • ハンドシャワーヘッド
    • ハンドシャワーホース
    • シャワーヘッドホルダー
    • シャワーバー & スライドレール
    • シャワーエンクロージャー
    • 蒸気シャワー室
    • ワールプールマッサージバスタブ
  • 室内装飾
    • キッチン&バスイベント
    • 温水ヒーターの修理
  • 配管用品
    • 編組フレキシブルホース
    • 真ちゅう製アングルバルブ
    • 配管工サービス
    • ポップアップ廃棄物排出
あなたはここにいる: ホーム / 浴室設備 / Install a Bathroom Drain Waste Vent System

Install a Bathroom Drain Waste Vent System

How to Install a Bathroom Drain Waste Vent System? Installing Drain Waste Vent Pipe is a professional plumber task. Running the pipe can be tricky. All different kinds of fittings are available to turn in different and receive different sizes of pipe at various angles. One fitting may need 3 opening ports, all accommodating a different size pipe. You will have to plan your runs and buy the necessary fittings (always get a few extra). Keep in mind that codes may regulate how fittings can be used (i.e. sanitary tees may not be used in vertical to horizontal connections; long sweep connection must be used here). You will need to know the diameter of your pipes, their angles, the code and their direction to determine each fitting. While planning may take some time and study, the cutting and assembly of plastic pipe is very simple.

1. Using a back saw or a fine toothed saw, cut the pipe the required length, remembering that the pipe fits into the fitting a prescribed distance for each diameter of pipe.

2. Use a small knife or rough sandpaper to remove the “burr” off the freshly cut pipe.

3. With a rag and some cleaning solvent, clean the ends of the pipe and the inside of fitting where the pipe will join. (ABS does not need this solvent or primer. It can be wiped clean with a damp rag.)

4. The glue will dry almost immediately and you can never get it unglued. To change the connection you must cut out the fitting and start over. Because of this, you want to be sure you have it right the first time. This is very easy in some cases, but often you will have a number of pipes coming into a fitting from several different angles. All of these must meet correctly once they are permanently glued. To assure this, “dry fit” the fittings and pipe by cutting and assembling everything without glue to assure it all fits at the correct angles and dimensions.

5. Make marks across fittings and pipe so that once the pipes are removed and the glue is spread, you will know exactly how to realign everything when the pipes are inserted permanently into the fitting. (Be sure the marks or lines are long enough on the pipe so that they will not be covered by the glue you will spread on the pipe.)

6. Spread a generous amount of the required pipe glue around the end of the pipe and on the inside of the fitting with a dauber.

7. Insert the pipe into the fitting until it “bottoms out” and give it a little twist to be sure that the glue is spread evenly.

One of the most difficult parts about running drain waste vent pipes is drilling the large (2-3″) holes necessary to run the pipe. You will need to purchase, borrow or rent special heavy duty plumbers’ bits that are notched to fit 1 1/2″, 2″ そして 2 1/2″ パイプ. The cheaper hole saw is just too difficult when you are doing a large project. You will also need a heavy duty 1/2″ or 3/4″ drill (preferably a right angle drill or one with a right angle attachment). Be careful, as drilling with these large bits often causes the bit to bind and the drill to spin.

あなたはおそらくそれも好きでしょう

  • Bathroom Sink Drain Trap Installation DIY Tips
    シンクドレントラップとポップアップ廃棄物設置ガイダンス
  • How to Install a Bathtub Drain
    バスタブドレンの設置ガイドとヒント
  • plumbing system
    配管システム: 冷温水分配, パイプ…
  • Clearing a Clogged Floor Drain pic
    詰まった床ドレンの除去
  • How to clean a clogged plumbing drain pipe?
    詰まった排水管を掃除する方法?
  • bathroom-p-trap
    Sanliv洗面台またはバスルームシンク排水P-トラップ
  • Ball Valve Installation in 9 easy steps
    でのボールバルブの取り付け 9 簡単な手順
  • How to install Pop-up Wastes and Traps
    Best Tips on How to Install Pop-up Wastes and Traps
  • Slotted Rod Operated Pop-Up Basin Waste
    How To Install A Push Pull Lever Rod Basin Pop Up Waste
  • Switching from cast iron to copper piping
    Switching from cast iron to copper piping
  • Bathroom Basin Pop Up Drain Waste
    Bathroom Sink or Basin Pop Up Waste Leaks Repair
  • Installing a New P-trap under Your Bathroom Sink
    浴室の流しの下に新しいPトラップを設置する

下に提出: 浴室設備, 配管設備 & 用品 タグ付け: 浴室床ドレン, drain

プライマリサイドバー

サイトを検索

翻訳

EnglishDeutschEspañolPortuguêsFrançaisItalianoРусскийالعربية日本語
デフォルトの言語として設定
 翻訳を編集

Sanliv Onlinestore

Twin roll toilet tissue paper holder

配管設備

  • 自動蛇口
  • 浴室付属品
  • 折りたたみシャワーフットレスト
  • キッチン蛇口
  • 拡大鏡
フィリップ・スタークの蛇口: アクサースタルクオーガニックバイハンスグローエ
シングルハンドルプルダウンキッチン蛇口ブラッシュゴールド
シェービングレッグ用Sanlivシャワーフットレスト,壁掛けシャワーステップフットレスト,ローレット真鍮バーフットホルダーレッジ,マットブラック
Sanlivシャワーフットレスト,脚を剃るコーナーフットレスト,ローレット真鍮バー フット ステップ シャワー棚,つや消しニッケル
シングルハンドルプルダウンキッチン蛇口つや消しニッケル
マットブラック単穴ハンドル浴室のシンクの蛇口
シングルハンドル浴槽シャワー混合栓
ホテルタオルホルダーオーガナイザートイレ壁棚つや消しニッケル

著作権 © 2025 バスルーム-キッチン-Faucets.comwith サイトマップ