How to fix a leaky bathroom faucet? Lesson to Replace Leaky Bathroom Faucets. Tips on how to Install a Bathroom sink Faucet. Replacing an old leaky bathroom basin faucet can be done by yourself.
Materials List to Replace a Bathroom Faucet
Robinet
Pop-up drain assembly
Pipe joint compound
Bande de téflon
Plumber’s putty
Penetrating oil
General Safety
Do not attempt a potentially dangerous project when you are tired, irritated, sick or under the influence of drugs or alcohol.
Wear approved eye protection when working with power tools or striking tools such as hammers.
When working in dusty situations, wear a dust filter mask over your mouth and nose.
Make sure you check building codes for your area before planning construction projects.
Keep all blades, bits and other cutting parts sharp on both power tools and hand tools. Dull tools can require you to apply extra force, which can lead to injuries.
Make sure you have a safe work environment that is well lit and free from obstructions and interference from clothing, long hair and jewelry.
Turn off breakers or remove fuses when working on all electrical projects.
Replacing a Bathroom Faucet Introduction
Lorsque vous remplacez un vieux robinet, il y a généralement trois choses à considérer: Combien de trous votre évier, À quelle distance ils sont, et si vous devrez ou non remplacer le drain.
La plupart des lavabos de salle de bain sont généralement livrés avec trois configurations de trous différentes. La configuration la plus populaire est deux trous à quatre pouces d'intervalle au centre avec un trou central entre eux (Trois trous totaux). Une autre configuration similaire est à deux trous de huit pouces d'intervalle au centre avec un trou central entre eux (Souvent appelé une configuration de jeu d'écart). finalement, Il pourrait y avoir juste un seul trou, qui est une configuration commune pour les éviers et les robinets plus récents.
Vous devrez acheter un robinet qui correspond à votre modèle de trou particulier. Il n'est pas recommandé d'essayer de percer des trous dans votre évier ou d'essayer de faire un ensemble de propagation dans un 4 Configuration de pouces. Une exception à cette règle, toutefois, Peut être fait pour certains robinets à trou unique conçus avec une base large qui couvrira les trous supplémentaires dans une configuration de 4 pouces.
habituellement, C'est une bonne idée de remplacer le drain lors du remplacement du robinet. Typiquement, Les robinets de salle de bain sont vendus avec des drains pop-up mais vous pouvez également les obtenir avec juste une prise. Si vous remplacez le drain, Envisagez également d'acheter un nouveau piège et un nouveau coin. Il est beaucoup plus facile de travailler avec de nouveaux tuyaux qu'anciens et le coût n'est pas prohibitif.
Helpful Tips to install a bathroom faucet
Make sure to wear safety glasses when working under the sink as bits of rust and metal can fall into your eyes as you are working.
Know where the main water shut off is just in case.
Have a small pail ready to catch leaks.
If you just can’t get the old faucet or drain out, consider replacing the sink as well. This course might still be cheaper than calling a plumber who might just tell you to replace the sink anyway.
STEP BY STEP Instructions to Replace a Leaky Bathroom Faucet
1.
Turn off the water to the existing faucet at the shutoff valves. ensuite, relieve pressure in the faucet by turning the hot and cold valves on.
2.
Remove the hot and cold supply tubes to the faucet. If you are replacing the drain with the new faucet, also remove the P-trap, and the linkage to the pop-up drain.
3.
Aussi, if you are replacing the drain, unscrew the nut holding the rubber gasket against the sink. Suivant, try to unscrew the drain flange from the T-connector. If this does not work (as it often does not) take a reciprocating saw (with a metal cutting blade) and cut the drain assembly in half just above the nut.
4.
To remove the faucet, use your basin wrench to unscrew the nuts under the faucet. Si nécessaire, use penetrating oil to get the nuts to turn and make sure you are unscrewing them the right way as it is easy to get disoriented under the sink. When the faucet is out scrape away any old plumbers putty or caulk with a putty knife.
5.
Some new faucets come with gaskets that seal between them and the sink while others require that you apply plumbers putty to make the seal. If yours is the latter, apply a generous amount of putty under the faucet so that it squeezes out as you put the faucet in place. Suivant, tighten the nuts under the faucet until the faucet is secure while also making sure that it is properly aligned.
6.
Wrap all the inlet fittings with Teflon Tape to ensure a tight seal before connecting hookups. Wrap the tape in the same direction as you will attach the fittings. To install the hookups, first attach them to the faucet with the help of the basin wrench and then to the shutoff valves using an adjustable wrench. Be careful not to twist them as you install them as this can restrict the water supply to the faucet and cause premature failure.
7.
Assemble the new drain (if it does not come already assembled) by first applying pipe joint compound on the tailpiece and then screwing it into the T-connector. When finished, screw the nut all the way down on the T-connector followed by the plastic washer and rubber gasket. It is important that there be a washer between the nut and rubber gasket.
8.
Put a heavy bead of plumbers putty around the drain flange and press it into the drain hole. Suivant, coat the threads on the drain body with pipe joint compound and from under the sink screw the drain body into the drain flange. Once the flange and body are together, tighten the nut on the body till the gasket is pressed tightly against the underside of the sink. Make sure that when tight, the branch on the T-connector is facing towards the back of the sink.
9.
To install the pop-up linkage, first place the pop-up in the drain hole making sure that the slot in the bottom of the pop-up is facing the back of the sink. Suivant, install the pivot rod in T-connector so that the rod finds the slot in the pop-up. Once lined up install the rods retaining nut snug so that the rod can still move but has no play.
10.
Insert the lift rod into the faucet and from below attach the clevis to the rod. With the lift rod down and the pop-up in the open position, insert the pivot rod into the nearest hole on the clevis while also having the rod pass through the spring clip. If all is aligned correctly the pop up should close when the lift rod is pulled up and open when it is put down again. Si non, make adjustments via the clevis screw.
11.
finalement, unscrew the aerator from the spout, open the water shutoffs and turn the faucet on for several minutes. Check for leaks and then reinstall the aerator.
What Kind of Bathroom Faucet do you want?
Single-hole and single-lever faucets integrate the spout and mixing handle or handles into one fitting. Compact and easy-to-use, they require only one faucet hole drilling. Some faucets will include an optional six-inch cover plate for existing four-inch drill installations.
Centerset faucets for standard four-inch drill installations handles mounted onto a six-inch plate. These are recommended for smaller, pre-existing, pre-drilled basins.
Widespread faucets offer the greatest design flexibility. A mini-widespread faucet has three separate pieces in a smaller, standard four-inch drilling. A widespread faucet has a standard spread or drilling of at least eight inches.
Wall-mounted faucets for above-the-counter and freestanding basins require a longer spout for extended reach.
In the bath, the faucet is typically set in either 4” or 8” width configurations. In the 4″ set you can have a centerset or mini widespread setup; if it is 8″ or more, it is known as a widespread set. When you choose your new faucet, you can change styles, but will have to stay with the same size, or replace the sink if you want to switch.
