How to Replace and Install a Single Handle Bathroom Faucet? Changing a bathroom-sink faucet is similar to fix a kitchen sink faucet. The main difference is that the assembly for a lavatory-sink faucet includes a pop-up assembly that allows the user to open and close the drain. There are a lot of new styles of Single Handle Bathroom Sink Faucets from global manufacturers today. Think well if you decide to replace a new one before start.
Matériaux et outils:
- basin cock wrench
- Phillips- and flat-head screwdrivers
- slip-joint pliers
- adjustable pliers
- adjustable wrench
- Teflon paste (or Teflon tape)
- bathroom caulk and caulk gun (or plumber’s putty)
- new supply tubes
IMPORTANT: Lisez ceci avant de commencer
- Introduction:
Lorsque vous remplacez un vieux robinet, il y a généralement trois choses à considérer: Combien de trous votre évier, À quelle distance ils sont, et si vous devrez ou non remplacer le drain. - La plupart des lavabos de salle de bain sont généralement livrés avec trois configurations de trous différentes. La configuration la plus populaire est deux trous à quatre pouces d'intervalle au centre avec un trou central entre eux (Trois trous totaux). Une autre configuration similaire est à deux trous de huit pouces d'intervalle au centre avec un trou central entre eux (Souvent appelé une configuration de jeu d'écart). finalement, Il pourrait y avoir juste un seul trou, qui est une configuration commune pour les éviers et les robinets plus récents.
- Vous devrez acheter un robinet qui correspond à votre modèle de trou particulier. Il n'est pas recommandé d'essayer de percer des trous dans votre évier ou d'essayer de faire un ensemble de propagation dans un 4 Configuration de pouces. Une exception à cette règle, toutefois, Peut être fait pour certains robinets à trou unique conçus avec une base large qui couvrira les trous supplémentaires dans une configuration de 4 pouces.
- habituellement, C'est une bonne idée de remplacer le drain lors du remplacement du robinet. Typiquement, Les robinets de salle de bain sont vendus avec des drains pop-up mais vous pouvez également les obtenir avec juste une prise. Si vous remplacez le drain, Envisagez également d'acheter un nouveau piège et un nouveau coin. Il est beaucoup plus facile de travailler avec de nouveaux tuyaux qu'anciens et le coût n'est pas prohibitif.
Step by Step Instructions:
Étape 1: Remove the P-trap
- Turn off the water at the shutoff valves underneath the sink.
- Loosen the collar nuts on the curved section of the drain pipe called the P-trap. Place a bucket underneath to catch any excess water, then remove the P-trap.
Étape 2: Free the Pop-up Assembly
- Use slip-joint pliers to loosen the nut holding the pop-up assembly in place under the sink.
- From overhead, unscrew the pop-up flange to free the assembly underneath the sink.
Étape 3: Remove the Supply Tubes and Mounting Nuts
- With the pop-up assembly out of the way, use a wrench to loosen and remove the fittings that join the old faucet’s supply lines to the shutoff valves.
- Using a basin wrench, reach behind the sink bowl and loosen and remove the supply tubes and the mounting nuts holding the faucet in place. Lift the old faucet off the sink. Use a rag or an abrasive pad to clean any residue left from underneath the old faucet.
- You may want to use flexible connectors to replace the rigid tubes connecting the faucet to the shutoff valves. Si c'est le cas, connect them to the new faucet. Don’t over-tighten.
Étape 4: Place the New Bathroom Sink Faucet
- Drop the new faucet in place, feeding the supply lines through the holes in the sink and making sure that the faucet’s gasket seats properly.
- Secure the faucet from underneath the sink with mounting nuts.
- Connect the bottoms of the flexible connectors to the hot- and cold-water shutoffs. Tighten all connections.
Étape 5: Install the Pop-up Assembly
- With the faucet in place, begin installing the pop-up assembly. Push the pop-up rod down through the faucet body, and attach the flat bar.
- Add a little plumber’s putty to the bottom of the new flange, and hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink. Spin the ring to position it with the tailpiece underneath the sink.
- Working underneath the sink, tighten the nut on top of the tailpiece to secure the pop-up housing in place.
Étape 6: Finish Bathroom Faucet Installation
- Hook the pop-up lever onto the flat bar and secure it to the pop-up housing.
- From overhead, drop the stopper into the drain hole. Work the pop-up rod to make sure the stopper works properly.
- Replace the P-trap and tighten the collar nuts.
- Turn on the water supply and check for leaks.
This the six easy steps to install a single lever bathroom sink faucet. If you have better way for bathroom faucet replacement or installation, please do not forget to share with us!