Cómo reemplazar un grifo del lavabo del baño con una sola manija
How to Replace and Install a Single Handle Bathroom Faucet? Changing a bathroom-sink faucet is similar to fix a kitchen sink faucet. The main difference is that the assembly for a lavatory-sink faucet includes a pop-up assembly that allows the user to open and close the drain. There are a lot of new styles of Single Handle Bathroom Sink Faucets from global manufacturers today. Think well if you decide to replace a new one before start.
Materiales y herramientas:
llave inglesa para lavabo
Phillips- y destornilladores de punta plana
alicates para juntas deslizantes
alicates ajustables
llave ajustable
Pasta de teflón (o cinta de teflón)
calafateo de baño y pistola de calafateo (o masilla de fontanero)
new supply tubes
IMPORTANTE: Read this before you start
Introduction: When replacing an old faucet there are generally three things to consider: how many holes your sink has, how far apart they are, and whether or not you will need to replace the drain.
Most bathroom sinks usually come with three different hole configurations. The most popular configuration is two holes four inches apart on center with a center hole between them (three holes total). Another similar configuration is two holes eight inches apart on center with a center hole between them (often called a spread set configuration). Finalmente, there might be just a single hole, which is a common configuration for newer sinks and faucets.
You will need to purchase a faucet that matches your particular hole pattern. It is not recommended that you try drilling holes in your sink or try to make a spread set fit in a 4 inch configuration. One exception to this rule, sin embargo, can be made for some single hole faucets that are designed with a wide base that will cover the extra holes in a 4-inch configuration.
Por lo general, it is a good idea to replace the drain when replacing the faucet. Típicamente, bathroom faucets are sold with pop-up drains but you can also get them with just a plug. If you do replace the drain, consider buying a new trap and tailpiece as well. It is much easier to work with new pipes than old and the cost is not prohibitive.
Step by Step Instructions:
Paso 1: Remove the P-trap
Turn off the water at the shutoff valves underneath the sink.
Loosen the collar nuts on the curved section of the drain pipe called the P-trap. Place a bucket underneath to catch any excess water, then remove the P-trap.
Paso 2: Free the Pop-up Assembly
Use slip-joint pliers to loosen the nut holding the pop-up assembly in place under the sink.
From overhead, unscrew the pop-up flange to free the assembly underneath the sink.
Paso 3: Remove the Supply Tubes and Mounting Nuts
With the pop-up assembly out of the way, use a wrench to loosen and remove the fittings that join the old faucet’s supply lines to the shutoff valves.
Using a basin wrench, reach behind the sink bowl and loosen and remove the supply tubes and the mounting nuts holding the faucet in place. Lift the old faucet off the sink. Use a rag or an abrasive pad to clean any residue left from underneath the old faucet.
You may want to use flexible connectors to replace the rigid tubes connecting the faucet to the shutoff valves. Si es así, connect them to the new faucet. Don’t over-tighten.
Paso 4: Place the New Bathroom Sink Faucet
Drop the new faucet in place, feeding the supply lines through the holes in the sink and making sure that the faucet’s gasket seats properly.
Secure the faucet from underneath the sink with mounting nuts.
Connect the bottoms of the flexible connectors to the hot- and cold-water shutoffs. Tighten all connections.
Paso 5: Install the Pop-up Assembly
With the faucet in place, begin installing the pop-up assembly. Push the pop-up rod down through the faucet body, and attach the flat bar.
Add a little plumber’s putty to the bottom of the new flange, and hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink. Spin the ring to position it with the tailpiece underneath the sink.
Working underneath the sink, tighten the nut on top of the tailpiece to secure the pop-up housing in place.
Paso 6: Finish Bathroom Faucet Installation
Hook the pop-up lever onto the flat bar and secure it to the pop-up housing.
From overhead, drop the stopper into the drain hole. Work the pop-up rod to make sure the stopper works properly.
Replace the P-trap and tighten the collar nuts.
Turn on the water supply and check for leaks.
This the six easy steps to install a single lever bathroom sink faucet. If you have better way for bathroom faucet replacement or installation, please do not forget to share with us!
