So reparieren Sie einen undichten Badhahn? Lektion zum Ersetzen von undichten Badarmaturen. Tipps zur Installation eines Waschbeckenhahns. Das Ersetzen eines alten undichten Wasserhahns im Badezimmer kann von Ihnen selbst durchgeführt werden.
Materials List to Replace a Bathroom Faucet
Wasserhahn
Pop-up drain assembly
Pipe joint compound
Teflon tape
Plumber’s putty
Penetrating oil
General Safety
Do not attempt a potentially dangerous project when you are tired, irritated, sick or under the influence of drugs or alcohol.
Wear approved eye protection when working with power tools or striking tools such as hammers.
When working in dusty situations, wear a dust filter mask over your mouth and nose.
Make sure you check building codes for your area before planning construction projects.
Keep all blades, bits and other cutting parts sharp on both power tools and hand tools. Dull tools can require you to apply extra force, which can lead to injuries.
Make sure you have a safe work environment that is well lit and free from obstructions and interference from clothing, long hair and jewelry.
Turn off breakers or remove fuses when working on all electrical projects.
Replacing a Bathroom Faucet Introduction
Beim Ersetzen eines alten Wasserhahns sind im Allgemeinen drei Dinge zu beachten: Wie viele Löcher hat dein Waschbecken?, wie weit sie voneinander entfernt sind, und ob Sie den Abfluss ersetzen müssen oder nicht.
Die meisten Waschbecken werden normalerweise mit drei verschiedenen Lochkonfigurationen geliefert. Die beliebteste Konfiguration sind zwei Löcher in einem Abstand von vier Zoll in der Mitte mit einem Mittelloch dazwischen (Insgesamt drei Löcher). Eine andere ähnliche Konfiguration sind zwei Löcher, die in der Mitte acht Zoll voneinander entfernt sind und zwischen denen sich ein Mittelloch befindet (wird oft als Spread-Set-Konfiguration bezeichnet). Schließlich, Es könnte nur ein einziges Loch geben, Dies ist eine übliche Konfiguration für neuere Spülen und Wasserhähne.
Sie müssen einen Wasserhahn kaufen, der Ihrem speziellen Lochmuster entspricht. Es wird nicht empfohlen, dass Sie versuchen, Löcher in Ihre Spüle zu bohren oder ein Spread-Set in eine zu passen 4 Zoll Konfiguration. Eine Ausnahme von dieser Regel, jedoch, kann für einige Einloch-Wasserhähne hergestellt werden, die mit einer breiten Basis ausgestattet sind, die die zusätzlichen Löcher in einer 4-Zoll-Konfiguration abdeckt.
Meistens, Es ist eine gute Idee, den Abfluss beim Ersetzen des Wasserhahns auszutauschen. Typischerweise, Badarmaturen werden mit aufklappbaren Abflüssen verkauft, aber Sie können sie auch mit nur einem Stecker erhalten. Wenn Sie den Abfluss ersetzen, Erwägen Sie auch den Kauf einer neuen Falle und eines neuen Saitenhalters. Es ist viel einfacher, mit neuen Rohren als mit alten zu arbeiten, und die Kosten sind nicht unerschwinglich.
Helpful Tips to install a bathroom faucet
Make sure to wear safety glasses when working under the sink as bits of rust and metal can fall into your eyes as you are working.
Know where the main water shut off is just in case.
Haben Sie einen kleinen Eimer bereit, um Leckagen zu fangen.
If you just can’t get the old faucet or drain out, consider replacing the sink as well. This course might still be cheaper than calling a plumber who might just tell you to replace the sink anyway.
STEP BY STEP Instructions to Replace a Leaky Bathroom Faucet
1.
Turn off the water to the existing faucet at the shutoff valves. Dann, relieve pressure in the faucet by turning the hot and cold valves on.
2.
Remove the hot and cold supply tubes to the faucet. If you are replacing the drain with the new faucet, also remove the P-trap, and the linkage to the pop-up drain.
3.
Ebenfalls, if you are replacing the drain, unscrew the nut holding the rubber gasket against the sink. Nächster, try to unscrew the drain flange from the T-connector. If this does not work (as it often does not) take a reciprocating saw (with a metal cutting blade) and cut the drain assembly in half just above the nut.
4.
To remove the faucet, use your basin wrench to unscrew the nuts under the faucet. Wenn erforderlich, use penetrating oil to get the nuts to turn and make sure you are unscrewing them the right way as it is easy to get disoriented under the sink. When the faucet is out scrape away any old plumbers putty or caulk with a putty knife.
5.
Some new faucets come with gaskets that seal between them and the sink while others require that you apply plumbers putty to make the seal. If yours is the latter, apply a generous amount of putty under the faucet so that it squeezes out as you put the faucet in place. Nächster, tighten the nuts under the faucet until the faucet is secure while also making sure that it is properly aligned.
6.
Wrap all the inlet fittings with Teflon Tape to ensure a tight seal before connecting hookups. Wrap the tape in the same direction as you will attach the fittings. To install the hookups, first attach them to the faucet with the help of the basin wrench and then to the shutoff valves using an adjustable wrench. Be careful not to twist them as you install them as this can restrict the water supply to the faucet and cause premature failure.
7.
Montieren Sie den neuen Abfluss (if it does not come already assembled) by first applying pipe joint compound on the tailpiece and then screwing it into the T-connector. When finished, screw the nut all the way down on the T-connector followed by the plastic washer and rubber gasket. It is important that there be a washer between the nut and rubber gasket.
8.
Put a heavy bead of plumbers putty around the drain flange and press it into the drain hole. Nächster, coat the threads on the drain body with pipe joint compound and from under the sink screw the drain body into the drain flange. Once the flange and body are together, tighten the nut on the body till the gasket is pressed tightly against the underside of the sink. Make sure that when tight, the branch on the T-connector is facing towards the back of the sink.
9.
To install the pop-up linkage, first place the pop-up in the drain hole making sure that the slot in the bottom of the pop-up is facing the back of the sink. Nächster, install the pivot rod in T-connector so that the rod finds the slot in the pop-up. Once lined up install the rods retaining nut snug so that the rod can still move but has no play.
10.
Insert the lift rod into the faucet and from below attach the clevis to the rod. With the lift rod down and the pop-up in the open position, insert the pivot rod into the nearest hole on the clevis while also having the rod pass through the spring clip. If all is aligned correctly the pop up should close when the lift rod is pulled up and open when it is put down again. Wenn nicht, make adjustments via the clevis screw.
11.
Schließlich, unscrew the aerator from the spout, open the water shutoffs and turn the faucet on for several minutes. Check for leaks and then reinstall the aerator.
What Kind of Bathroom Faucet do you want?
Single-hole and single-lever faucets integrate the spout and mixing handle or handles into one fitting. Kompakt und einfach zu bedienen, they require only one faucet hole drilling. Some faucets will include an optional six-inch cover plate for existing four-inch drill installations.
Centerset faucets for standard four-inch drill installations handles mounted onto a six-inch plate. These are recommended for smaller, bereits vorhanden, pre-drilled basins.
Widespread faucets offer the greatest design flexibility. A mini-widespread faucet has three separate pieces in a smaller, standard four-inch drilling. A widespread faucet has a standard spread or drilling of at least eight inches.
Wall-mounted faucets for above-the-counter and freestanding basins require a longer spout for extended reach.
In the bath, the faucet is typically set in either 4” or 8” width configurations. In the 4″ set you can have a centerset or mini widespread setup; if it is 8″ or more, it is known as a widespread set. When you choose your new faucet, you can change styles, but will have to stay with the same size, or replace the sink if you want to switch.
